|
| |
 |
Advanced Gasket can supply sheet
rubber for all of your requirements. We stock excellent general
purpose & commercial grade gasket materials as well as Elastomers
where service is critical. If your requirement is for Mil-Spec
materials please contact our sales department for a quote. Rubber
materials can be purchased by the roll, sheet, strip or fabricated
into die cut parts. Please refer to our Web page under Rubber for
specs & application data. |
Neoprene
SBR / Neoprene / Nitrile Blend with moderate oil resistance. Commercial
grade, black plate finish. For use as bumpers, pads and in sealing and
general gasket applications. Meets ASTM D2000-BC (durometer dependent).
|
Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
Blended
CR/NBR/
SBR |
Black |
50-80 |
1000 (800) |
300 |
-20ºF to +170ºF |
1/16, 3/32, 1/8, 3/16, 1/4, 3/8, 1/2, 3/4, 1 |
Red Rubber
SBR sheet, non oil resistant. Cloth impression or plate
finish. Meets ASTM D1330 Grade I/II (depending on mfgr).
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
SBR
(styrene butadiene) |
Red |
70-80 |
700 (400) |
300 |
-20ºF to +170ºF |
1/16,
1/8,
3/16, 1/4 |
Nitrile (Buna-N)
NBR sheet, commercial grade, smooth finish. Excellent
resistance to oils, solvents and fuel. Meets ASTM D2000-BF.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
NBR
(butadiene-acrylonitrile) |
Black |
40-80 |
1000 |
300 |
-20ºF to +170ºF |
1/32, 1/16,
3/32, 1/8,
3/16, 1/4, 3/8,
1/2, 3/4, 1 |
White FDA Nitrile
White NBR Food-Grade sheet, made from FDA-approved
ingredients. Plate finish, good resistance to abrasion. Used for general
gasketing, countertops and skirting in all areas of food processing. Non
toxic and non-marking. Meets ASTM D2000-2BF.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
NBR
(butadiene-acrylonitrile) |
White |
60 |
1000 |
350 |
-25ºF to +180ºF |
1/16, 3/32,
1/8, 3/16, 1/4 |
EPDM
EPDM sheet, black plate finish, limited oil and ozone
resistance. Meets ASTM D2000-2BA, MIL R-3065.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
EPDM
(ethylene-propylene diene) |
Black |
40-70 |
800 |
300 |
-20ºF to +200ºF |
1/16, 3/32,
1/8, 3/16, 1/4 |
Natural Gum Rubber
Natural gum rubber sheet, natural color, smooth finish.
Excellent tear strength, abrasion resistance, resilient. Used in general
gasketing and as sand and shot blast curtain. Meets ASTM D2000.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
| NR (Gum) |
Natural |
40 |
3000 |
600 |
-20ºF to +140ºF |
1/16, 3/32,
1/8, 3/16, 1/4,
3/8, 1/2, 3/4, 1 |
Cloth Inserted
SBR/NBR sheet, smooth finish, 1 ply of fabric for every
1/16" thickness. Used where reduced creep and heavy flange load is
required. Meets ASTM D2000-BA.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
| SBR |
Black |
55-80 |
400 |
200 |
-20ºF to +170ºF |
1/16, 3/32,
1/8, 3/16, 1/4 |
Diaphragm Sheet
SBR/NBR sheet, smooth finish, 1 ply of fabric for every
1/16" thickness. Used where reduced creep and heavy flange load is
required. Meets ASTM D2000-BA.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
| Neoprene |
Black |
70 |
1100 |
300 |
-20ºF to +180ºF |
1/16, 1/8,
3/16, 1/4, |
Silicone Rubber Commercial
Grade
Commercial grade silicone rubber with smooth finish.
Excellent resistance to weathering and ozone, good resistance to hot water
and low pressure steam, alcohols, diethylene glycol and fair resistance to
petroleum base oils. Not recommended for service in aromatic solvents,
fuels, chlorinated solvents and acids. Meets MIL-R-5847D and ZZR765-C, Class
IIA and IIB; AMS 3301, 3302, 3303, 3304; ASTM D 2000 M1GE 405, 505, 605,
705.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
| Silicone |
Red |
40 |
725 |
300 |
-65ºF to +450ºF |
|
| Silicone |
Red |
50 |
725 |
250 |
-65ºF to +450ºF |
1/32,1/16, 3/32 |
| Silicone |
Red |
60 |
725 |
200 |
-65ºF to +450ºF |
1/8, 3/16, 1/4 |
| Silicone |
Red |
70 |
725 |
150 |
-65ºF to +450ºF |
|
FDA Silicone
Rubber Red
FDA approved ingredients per 21CFR 177.2600.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
| Silicone |
Red |
40 |
650 |
350 |
-65ºF to +400ºF |
|
| Silicone |
Red |
50 |
650 |
250 |
-65ºF to +400ºF |
1/32,1/16, 3/32 |
| Silicone |
Red |
60 |
650 |
200 |
-65ºF to +400ºF |
1/8, 3/16, 1/4 |
| Silicone |
Red |
70 |
650 |
150 |
-65ºF to +400ºF |
|
| Silicone |
Red |
80 |
700 |
150 |
-65ºF to +400ºF |
|
FDA Silicone
Rubber White
FDA approved ingredients per 21CFR 177.2600.
| Elastomer |
Color |
Available Durometer
(SHORE A) |
Typical Tensile
PSI (Minimum) |
Ultimate
Elongation
(%Min) |
Temperature
Range |
Standard Thicknesses |
| Silicone |
White |
40 |
650 |
350 |
-65ºF to +400ºF |
|
| Silicone |
White |
50 |
650 |
250 |
-65ºF to +400ºF |
1/32,1/16, 3/32 |
| Silicone |
White |
60 |
650 |
200 |
-65ºF to +400ºF |
1/8, 3/16, 1/4 |
| Silicone |
White |
70 |
650 |
150 |
-65ºF to +400ºF |
|
| Silicone |
White |
80 |
700 |
150 |
-65ºF to +400ºF |
|
These properties were obtained using ASTM samples and should not be
used to set QC specification minimum requirements
|
